home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
SGI Freeware 2002 November
/
SGI Freeware 2002 November - Disc 2.iso
/
dist
/
fw_hylafax.idb
/
var
/
freeware
/
spool
/
fax
/
config
/
zyxel-1496e.z
/
zyxel-1496e
Wrap
Text File
|
2002-07-08
|
5KB
|
114 lines
# $Id: zyxel-1496e,v 1.2 2002/04/07 20:29:27 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for a ZyXEL U1496. Firmware revisions from
# 5.02 on should work, though rev 6.01 works much better.
# Actually, the preferred use is to get firwmare rev 6.13 or
# 6.14 and configure the modem to use Class 2.0; this file
# is kept around for folks with old firmware.
#
# This configuration file sets up the ZyXEL to run at 38.4 for
# both sending and receiving. RTS/CTS flow control is used on
# the tty port--you probably shouldn't use XON/XOFF. Note that
# on an SGI system the getty speed is the following non-standard
# gettydefs entry:
#
# dx_38400# B38400 # B38400 SANE TAB3 HUPCL #\r\n\n$HOSTNAME login: #dx_38400
#
# CONFIG: CLASS2: ZyXEL*1496*-*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 2 interface
ModemRate: 19200
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT&H0 # disable flow control
ModemHardFlowCmd: AT&H3 # hardware flow control
ModemSoftFlowCmd: AT&H4 # software flow control
ModemSetupDTRCmd: AT&D2 # DTR off causes modem to hang up
ModemSetupDCDCmd: AT&C1 # DCD tracks carrier
ModemSetupAACmd: AT+FAA=1 # enable in current class
#
ModemSendFillOrder: LSB2MSB # as expected
ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
Class2RecvDataTrigger: "\022" # a la 2388-B
#
# Additional reset commands:
#
# &B1 DTE-DCE rate is fixed at DTE setting
# &N0 Auto-negotiate highest possible DCE-DCE link rate
# &S0 DSR always on
# *F0 Deny remote configuration
# S18=2 Receive at 38400 (removed from default)
# S38.3=1 DCD on/off sequence follows UNIX standard; also
# fix receiving baud rate at S18 value
# S39=0 (avoid Class 2 compatibility hacks)
#
ModemResetCmds: AT&B1&N0&S0*F0S38.3=1S39=0
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# Unfortunately, ZyXEL's don't seem to detect a busy signal when
# the @ symbol is used to terminate the dialing string. Instead
# calls to a busy line come back with a NO CARRIER status which
# causes us to toss the job. Consequently we fall back to the
# normal method and raise the number of retries on a no carrier
# status. ZyXEL claims that this behaviour is not a bug, but
# rather that we are requesting ``an enhancement'' (never mind
# that their manual says that it should work).
#
ModemDialCmd: ATDT%s # no '@' 'cuz then busy not recognized
NoCarrierRetrys: 3 # retry 3 times on no carrier
#
ModemSetVolumeCmd: "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
#QualifyCID: etc/cid # CID access control list file
#CIDNumber: "CALLER NUMBER: " # pattern string for phone number info
#CIDName: "CALLER NAME: " # pattern string for identity info
#
PagerSetupCmds: AT&K0&N15 # use V.22 at 1200 bps (PageNet)
#
# Rev 6.1x firmware have a bug in the ECM support so
# explicitly disable it's use. To re-enable its use just
# comment out the following line.
#
Class2DCCQueryCmd: "!(0,1),(0-5),(0-4),(0-2),(0,1),(0),(0),(0-7)"